ITAR PCB Assembly

ITAR-Registered
PCB Assembly

PCB assembly for defense, aerospace, and government programs. 100% US-built at our California facility, backed by ISO 9001, ISO 13485, and IPC-trained assembly.

+1 916 692 9706

Overview

PCB assembly you can run through an ITAR workflow without compromise

Ansync Circuits is an ITAR-registered PCB assembly house. That registration is not a marketing line - it means our facility, personnel, and data-handling practices are set up to keep controlled technical data inside an authorized U.S. workflow, from the moment Gerbers and BOMs arrive through final shipment of the assembled board.

We build for defense primes, aerospace subcontractors, satellite programs, government labs, and industrial customers with dual-use hardware. The same SMT lines that assemble ISO 13485 medical devices handle ITAR work: jet-printed solder paste, high-precision Mycronic pick-and-place, 3D AOI and X-ray inspection, and IPC-trained rework - all in one California building, under one quality system.

Why Ansync

Built for the compliance posture defense and aerospace require

ITAR Registered

Registered and audit-ready

We maintain active ITAR registration with the U.S. Department of State. Access to technical data, work-in-process hardware, and finished assemblies is restricted to authorized personnel, and our storage and transmission practices are aligned with ITAR requirements.

US-Only Workflow

No offshore steps

Design, procurement, assembly, inspection, and testing all happen at our California facility - a baseline requirement for most defense programs.

Traceability

Full as-built record

Batch-level component traceability, per-board AOI imagery, and travelers give you the documentation program audits expect.

Inspection

3D AOI + X-Ray

Every board runs through 3D AOI and, when required, 3D X-ray - helping catch BGA and QFN defects before shipment.

Quality System

ISO 9001 + 13485

The same quality-management discipline that supports medical devices applies to ITAR work - process control, change management, and corrective action built in.

Capabilities

Full-service ITAR PCB assembly, from first run to production

Design for manufacturability, SMT and through-hole assembly, prototype builds, 3D AOI and X-ray inspection, functional testing, and IPC-trained rework - all under one roof.

01

Design

Custom PCB Design

Schematic capture and layout optimized for manufacturability, reliability, and cost.

02

Assembly

SMT and Through-Hole

High-mix and complex assemblies with accurate, repeatable results across volumes.

03

Prototyping

First-Run PCBs

Fast small and mid-run prototype builds to validate designs and refine processes.

04

Inspection

3D AOI and X-Ray

Automated optical and 3D X-ray inspection catch defects early and verify hidden joints.

05

Testing

Functional Testing

We perform functional testing using your documentation and fixtures before shipment.

06

Rework

PCB Rework and Repair

IPC-trained technicians handle component replacement, solder correction, and troubleshooting.

Certifications

The certifications behind ITAR-grade PCB assembly

ITAR registration rides on top of a robust quality and workmanship foundation - ISO 9001, ISO 13485, IPC-trained assembly, and fully domestic manufacturing.

ITAR Registered

ITAR Registered

Registered to build electronics for defense and aerospace.

  • Made in the USA Made in USA
  • ISO 13485 Certified ISO 13485 Certified
  • ISO 9001 Certified ISO 9001 Certified
  • IPC Certified Technicians IPC Certified

FAQ

ITAR PCB assembly - frequently asked questions

Is Ansync Circuits ITAR registered?
Yes. Ansync Circuits is ITAR registered with the U.S. Department of State and builds PCB assemblies for defense, aerospace, and government customers, including programs that involve defense articles and technical data covered by ITAR.
What does ITAR-registered PCB assembly mean for my program?
It means we meet the International Traffic in Arms Regulations requirements for handling, storing, and communicating technical data covered by ITAR. Gerbers, BOMs, firmware references, and assembled hardware for defense and aerospace builds stay within an authorized US workflow at every step.
Is all assembly performed in the United States?
Yes. All PCB design, component placement, inspection, and testing occur at our California facility. We do not offshore assembly steps - a hard requirement for most defense and aerospace customers.
Which industries do you build ITAR PCBs for?
Defense primes and subcontractors, aerospace, satellite and space hardware, government research labs, and dual-use industrial programs that require a US-based ITAR-registered assembler.
Do you combine ITAR handling with medical-grade quality systems?
Yes. Our facility is ITAR registered, ISO 9001 certified, and ISO 13485 certified, with IPC-trained technicians. The same traceability and process control that supports medical device builds applies to defense programs.
How do you handle traceability on ITAR jobs?
Every component is tracked from incoming batch to final placement, with AOI imagery captured for each assembled board. Travelers, batch photography, and pre-placement value checks give you a complete as-built record.

Get started

Ready to build
your next ITAR PCB?

Talk to our engineering team or request a quote for your defense or aerospace build today.

+1 916 692 9706